China Professional Cimc Huajun Hot 3axle Bulk Cement Tanker Trailer with Good quality

Product Description

Type bulk cement semi-trailer
MODEL ZCZ9404GFLHJF
Overall Dimensions 11090,10940,10090 * 2500 * 3950(mm)
Landing Leg Setting  2,500 mm
Wheelspan 5350+1310+1310(mm)
Axle Spacing  1310mm
King Pin Setting  1250mm

Tank:

Loading Capacity     40T(69M3)
Tank shell Q235,6mm thickness, and Q345 4mm
Dished ends Q235,6mm thickness
Pipe material Carbon steel
Discharging Hose Diameter 4″
Discharging valve 4″ butterfly valve
Discharging Hose Length 7.2m
Hose quick coupling 4″ female quick coupling.
Discharging capacity  ≥1m3/min
Working pressure 0.2 Mpa
Test pressure 0.3 Mpa
Manhole  3
MAX. Horizontal Discharging Distance 5,000 mm
MAX. Vertical Discharging Distance 15,000 mm

RUNNING GEAR:

Suspension  Undermount tri-axle suspension with equalizer;10-Leaf Spring
Axle Square axle,150X150mm.(FUWA 16T capacity)
Brake Dual line pneumatic brake system.
Parking Brake Type 30/30 spring brake system on 2 axles
Rim 8.5-20,10 holes steel Disc wheel, 12Pcs.
Tire 12.00R20  STEEL RADIUS TYRE, 12 Pcs  
King Pin  3.5″ 
LXIHU (WEST LAKE) DIS. LEG Two speed manual operation type with sand shoe.

PNEUMATIC SYSTEM:

Electromotor  4102 Made in China, (44Kw, 2000r/Min)
Air Compressor 12m3/min Made in China,Mounted at the front of trailer

ELECTRICAL:

Voltage 24 Volt
Receptacle 7 way
Light Front Marker Lamp : White
Side Marker Lamp Amber
Rear Lamp Red
Turn Signal Lamp Amber

STRUCTURAL WEIGHT RATING:

Tare Weight 81000KG,89000KG
Pay Load  31900KG,31100KG
G.V.W.R. 40000KG

PAINTING:

Painting As per client’s requirement

More photos for your reference:

Note : all the details not mentioned above should comply with Chinese regulations.

Company information: 

CIMC VECHICLE was founded by CIMC group, which fixes the mission to be customers’ partner for modern transportation. CIMC is dedicated to manufacturing and supplying CIMC trucks, CIMC truck body assembly, trailers, tank equipment. Currently, CIMC owns USD 8.8 billion total assets, USD 2.6 billion net assets, USD 8.4 billion annual sales and USD 0.6 billion net profits in 2571, having over 150 subsidiaries and 63, 000 staff across China, North America, Europe, Asia and Australia. 
Vehicles: CIMC has over 1000 lines of products in 11 series, including container chassis, flatbed trailer, bulk lorry, tanker, self-dumper, reefer trailer, van, curtain side trailer, mixer, pump truck, car carrier vehicle, fire engine, sanitation vehicle, etc. With the annual output capacity of over 200 thousand units, it now takes the leading position in the world. Up to today, the Group has established 22 production bases. 
Heavy Truck: Have its own production C & C brand truck. Other heavy truck CIMC produces the truck body, more than 2, 000 kinds of truck body for different transportation purpose. The truck chassis cooperates with FAW, XIHU (WEST LAKE) DIS.FENG DFAC, SHACMAN, SINOTRUK, FOTON, BEI BEN, JAC, CAMC, ZheJiang HYUNDAI, SAIC-Iveco and so on, include all truck chassis brand production in China. 

FAQ

Q1. Are you a manufacturer? 
Yes, we have been in special vehicle manufacturing and marketiing for over 20 years. 

Q2. What markets do your vehicle export to? 
Europe, North & South America, South-East Asia, Africa, Oceanica, Middle East countries etc. 

Q3. What information should I let you know if I want to get a quotation? 
Please let us know the your purpose, road condition, cargo type, tons of your cargo, dimensions of trailer, quantity etc. The more info you provide, the more accurate model and price you will get. 

Q4. Is it available to print our own brand on the vehicle? 
Totally acceptable as you wish. 

Q5. How can I get the price of your vehicle? 
You can connect with us through any of the following contact information. Our personalized service person will respond you within 24 hours. 

Contact information: 

HangZhou CIMC HUAJUN VEHICLE Co., Ltd. 
Huajun Avenue, HangZhou District, HangZhou, ZheJiang , China
 
 
 
 

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are 2 main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on 1 side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between 2 and 16 inches. A screw with a pointy tip has a smaller major diameter than 1 without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is 1 element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.
screwshaft

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of 1 thread to the corresponding point on the next thread. Measurement is made from 1 thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in 1 revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.
screwshaft

The lead of a screw shaft

Pitch and lead are 2 measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are 2 ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with 2 or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are 2 types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.
screwshaft

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.

China Professional Cimc Huajun Hot 3axle Bulk Cement Tanker Trailer   with Good qualityChina Professional Cimc Huajun Hot 3axle Bulk Cement Tanker Trailer   with Good quality